Estoy pensando adquirir el DIVIDE

Si por algo se caracteriza el Spectrum es por su gran variedad de periféricos (clásicos y modernos)

Moderador: Sir Cilve Sinclair

lmdiaz1
rst 0
Mensajes: 1
Registrado: Lun Jul 29, 2013 10:49 am

Re: Estoy pensando adquirir el DIVIDE

Mensaje por lmdiaz1 » Lun Jul 29, 2013 11:31 am

Pues yo no tengo ni idea de todas estas cosas tecnicas porque sera mi primer DIVIDE el que me haga Flopping, que ya compré en ebay hace muchos meses el adaptador IDE para un tarjeta SD
Animo Flopping a por ello

Spezzi63
rst 0
Mensajes: 3
Registrado: Dom Abr 15, 2018 4:57 pm

Re: Estoy pensando adquirir el DIVIDE

Mensaje por Spezzi63 » Vie Abr 20, 2018 5:15 pm

El artículo ya no está disponible
Última edición por Spezzi63 el Dom Nov 19, 2023 4:04 pm, editado 1 vez en total.

Avatar de Usuario
JULIO
Freddy Hardest
Mensajes: 599
Registrado: Mar May 08, 2007 10:30 am
Ubicación: Castilla La Mancha.

Re: Estoy pensando adquirir el DIVIDE

Mensaje por JULIO » Mar Abr 24, 2018 11:47 pm

Hello.
I do not have the special version for TK90X, leave the jumper open and try again, spectrum +2A isn't a (illegal) Brazilian Clone.
And another very important question, please make a deep clean of expansion bus.
regards.

semos internacionales... :lol:

Spezzi63
rst 0
Mensajes: 3
Registrado: Dom Abr 15, 2018 4:57 pm

Re: Estoy pensando adquirir el DIVIDE

Mensaje por Spezzi63 » Mié Abr 25, 2018 12:21 am

El artículo ya no está disponible
Última edición por Spezzi63 el Dom Nov 19, 2023 4:05 pm, editado 1 vez en total.

Avatar de Usuario
JULIO
Freddy Hardest
Mensajes: 599
Registrado: Mar May 08, 2007 10:30 am
Ubicación: Castilla La Mancha.

Re: Estoy pensando adquirir el DIVIDE

Mensaje por JULIO » Mié Abr 25, 2018 10:29 am

Hello.
Under the eeprom socket two diodes and a 10K resistor are required.
But this image should help you.
Taken from version d2 in velesoft web page:
These versions d2,d3...d4 are special for brazilian clones TKs, for +2a works with less components.
Imagen
(please resize the caption) this message board do not fit the images.
With the info taken from version d2 and laters...
For the spectrum +2A/B +3 the config of some jumpers:
CLOSE JP1
CLOSE JP2 FOR ENABLE FLASH FIRMW IN EPROM
CLOSE JP3 this are only for +2A/B +3
if you use +3e ROMS in the +2A/B +3 ...CLOSE JP4 & JP6
if not leave OPEN.
For +2A/B +3 only:
don't solder D5(1N4148),D6(1N4148), R16(220R)
(please fit to page) or "save img as"
Imagen
...version d4 are UNTESTED by the autor.
Hope you find this info usefull.
You do not get offended, because it is difficult to express myself in a language that I do not master to perfection.
The author of the page is a very friendly and helpful person, write directly to him, who will be able to help him for sure.
He has helped me with many doubts, I have always managed to fix the problems I had writing to him.
regards
Julio.

Spezzi63
rst 0
Mensajes: 3
Registrado: Dom Abr 15, 2018 4:57 pm

Re: Estoy pensando adquirir el DIVIDE

Mensaje por Spezzi63 » Mié Abr 25, 2018 5:45 pm

El artículo ya no está disponible
Última edición por Spezzi63 el Dom Nov 19, 2023 4:05 pm, editado 1 vez en total.

Avatar de Usuario
JULIO
Freddy Hardest
Mensajes: 599
Registrado: Mar May 08, 2007 10:30 am
Ubicación: Castilla La Mancha.

Re: Estoy pensando adquirir el DIVIDE

Mensaje por JULIO » Jue Abr 26, 2018 1:32 pm

Hello.
How have you checked for errors?
The recommendable thing is:
-check Z80 in +2A pcb, M1 line.
-test soldered resistor values.
-correct orientation of capacitors with polarity and transistors.
-remove trs and check transistors off pcb.
-check and verify that jumper switchs really close the jumpers. use good jumper switchs.
-Remove all the components in socket.
-check again TTL components off pcb.
-check SRAM off pcb.
-verify GAL with programmer.
-use a programmed EPROM 2764 with standalone programmer off pcb and with permutor contents of TBIOS or EEPROM in 28c64 socket.
-Deep cleaning with isopropyl alcohol of pcb.
-Drying with compressed air of pcb.
-Check the solder points for short circuits or poor solder in some places.
-Open circuit editing program (e a g l e ) and use a multimeter checking line by line from the expansion bus. HARD, BUT NECESSARY
-Check the solder points for short circuits.
It is possible that the printed circuit board has a manufacturing error.
regards
Julio.

Responder

¿Quién está conectado?

Usuarios navegando por este Foro: No hay usuarios registrados visitando el Foro y 11 invitados